当前位置:首页 >> 机械/仪表 >>

SONY CCU-590 摄像机控制单元 操作手册


CAMERA CONTROL UNIT

CCU-590/590P

OPERATION MANUAL [English] 1st Edition

WARNING
To prevent fire or shock hazard, do not expose the unit to rain or moisture. To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. THIS APPARATUS MUST BE EARTHED. AVERTISSEMENT Afin d’éviter tout risque d’incendie ou d’électrocution, ne pas exposer l’appareil à la pluie ou à l’humidité. Afin d’écarter tout risque d’électrocution, garder le coffret fermé. Ne confier l’entretien de l’appareil qu’à un personnel qualifié. CET APPAREIL DOIT ?TRE RELI? ? LA TERRE. WARNUNG Um Feuergefahr und die Gefahr eines elektrischen Schlages zu vermeiden, darf das Ger?t weder Regen noch Feuchtigkeit ausgesetzt werden. Um einen elektrischen Schlag zu vermeiden, darf das Geh?use nicht ge?ffnet werden. ?berlassen Sie Wartungsarbeiten stets nur qualifiziertem Fachpersonal. DIESES GER?T MUSS GEERDET WERDEN.
WARNING: Using this unit at a voltage other than 120 V may require the use of a different line cord or attachment plug, or both. To reduce the risk of fire or electric shock, refer servicing to qualified service personnel.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

Attention-when the product is installed in Rack: 1.Prevention against overloading of branch circuit When this product is installed in a rack and is supplied power from an outlet on the rack, please make sure that the rack does not overload the supply circuit. 2.Providing protective earth When this product is installed in a rack and is supplied power from an outlet on the rack, please confirm that the outlet is provided with a suitable protective earth connection. 3.Internal air ambient temperature of the rack When this product is installed in a rack, please make sure that the internal air ambient temperature of the rack is within the specified limit of this product. 4.Prevention against achieving hazardous condition due to uneven mechanical loading When this product is installed in a rack, please make sure that the rack does not achieve hazardous condition due to uneven mechanical loading. 5.Install the equipment while taking the operating temperature of the equipment into consideration For the operating temperature of the equipment, refer to the specifications of the Operation Manual. 6.When performing the installation, keep the following space away from walls in order to obtain proper exhaust and radiation of heat. Right, Left : 4 cm (1.6 inches) or more Rear : 10 cm (4 inches) or more For the customers in the U.S.A. (for CCU-590) This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
You are cautioned that any changes or modifications not expressly approved in this manual could void your authority to operate this equipment. The shielded interface cable recommended in this manual must be used with this equipment in order to comply with the limits for a digital device pursuant to Subpart B of Part 15 of FCC Rules.

2

For the customers in Europe (for CCU-590P) This product with the CE marking complies with both the EMC Directive (89/336/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European standards: ? EN60950: Product Safety ? EN55103-1: Electromagnetic Interference(Emission) ? EN55103-2: Electromagnetic Susceptibility(Immunity) This product is intended for use in the following Electromagnetic Environment(s): E1 (residential), E2 (commercial and light industrial), E3 (urban outdoors), E4 (controlled EMC environment, ex. TV studio) Pour les clients européens (pour CCU-590P) Ce produit portant la marque CE est conforme à la fois à la Directive sur la compatibilité électromagnétique (EMC) (89/336/CEE) et à la Directive sur les basses tensions (73/23/CEE) émises par la Commission de la Communauté européenne. La conformité à ces directives implique la conformité aux normes européennes suivantes : ? EN60950 : Sécurité des produits ? EN55103-1 : Interférences électromagnétiques (émission) ? EN55103-2 : Sensibilité électromagnétique (immunité) Ce produit est prévu pour être utilisé dans les environnements électromagnétiques suivants : E1 (résidentiel), E2 (commercial et industrie légère), E3 (urbain extérieur) et E4 (environnement EMC contr?lé ex. studio de télévision). Für Kunden in Europa (für CCU-590P) Dieses Produkt besitzt die CE-Kennzeichnung und erfüllt die EMV-Richtlinie (89/336/EWG) sowie die Niederspannungsrichtlinie (73/23/EWG) der EGKommission. Angewandte Normen: ? EN60950: Sicherheitsbestimmungen ? EN55103-1: Elektromagnetische Vertr?glichkeit (St?raussendung) ? EN55103-2: Elektromagnetische Vertr?glichkeit (St?rfestigkeit), für die folgenden elektromagnetischen Umgebungen: E1 (Wohnbereich), E2 (kommerzieller und in beschr?nktem Ma?e industrieller Bereich), E3 (Stadtbereich im Freien) und E4 (kontrollierter EMV-Bereich, z.B. Fernsehstudio)

3

Table of Contents
Overview ............................................................................... 5 Function and Location of Parts and Controls ................... 6 Front panel ................................................................................ 6 Rear panel ................................................................................. 7 Internal power switch and internal boards.............................. 10 Connecting the CCU-590/590P to the Video Camera ...... 11 Notes on connections .............................................................. 11 Self-Diagnostics ................................................................. 12 Settings of the camera.............................................................. 12 Status display of the camera system ........................................ 12 Self-diagnostics of the camera system..................................... 12 Self-diagnostics results of the CCU-590/590P internal boards ... 13 Self-diagnostics results of the camera internal boards ............ 15 ROM version indication .......................................................... 15 Exiting the Self-diagnostic mode............................................. 15 When an error occurs............................................................... 15 Specifications ..................................................................... 16 General..................................................................................... 16 Input signals............................................................................. 16 Output signals .......................................................................... 16 Camera input/output signals .................................................... 16 Supplied accessories ................................................................ 16 Optional accessories ................................................................16

4

Table of Contents

Overview
The CCU-590/590P Camera Control Unit provides a variety of remote control and adjustment functions for the processing of signals from a BVP-E10/E10P/E10WS/ E10WSP/E30/E30P/E30WS/E30WSP CCD Color Video Camera, and can be used in Electronic Field Production (EFP) or studio work. The CCU-590/590P has the following features:

Wide variety of system configurations
? The optional CA-905K/F/T/L large-lens adaptor allows a large lens to be fitted onto the portable video camera and used in conjunction with the BVF-77/77CE 7-inch B/W Viewfinder. ? 3 output lines (composite video or SDI can be selected as the output signal) are provided. ? When equipped with the optional RM-B750 Remote Control Unit, the RM-B750 can be used to control the video camera directly, without the use of a RCP-750/751 Remote Control Panel.
Note

The RM-B750 does not work when the CCU-590/590P is connected to the CNU-700 Camera Network Unit. ? The CCU-590/590P supports communications between the video camera and the CCU-590/590P over either a triax cable or coaxial cable. (Power, however, is not supplied to the video camera in the case of coaxial cable.)

10-MHz, wideband triax transmission
? Wideband triax transmission with Y signal at 10 MHz, R-Y and B-Y signals at 6 MHz is used for inputting video signals from the video camera. Maximum length of triax cable is 700 meters (with diameter of 8.5 mm), 1,050 meters (BELDEN 9232 with diameter of 13.2 mm), or 1,400 meters (with diameter of 14.5 mm). ? The CCU-590/590P supports prompter signal transmission.

Rack mountable
Two CCU-590/590Ps can be mounted side by side in a standard 19-inch EIA rack when using an optional RMM301 Rack Mount Adaptor.

Overview

5

Function and Location of Parts and Controls
Front panel

aCamera number sheet/tally indicator b POWER switch/CAM and MAIN indicators c CABLE ALARM indicators

CAM MAIN " OPEN SHORT 1
MIC – ON OFF PGM PRIV PGM PROD

d INCOM input/output/setting section

a Camera number sheet/tally indicator Lights red when the red tally signal is input (e.g. when the video signal from the video camera connected to the CCU590/590P goes on air). When the CALL button on the video camera, MSU-900/950, RCP-750/751 series remote control panel, or an optional RM-B750 is pressed, the indicator lights if it is not lit, and goes off if it is lit. The indicator lights green when the green tally signal is input (e.g. when the video signal from the camera connected to the CCU-590/590P goes off air). Attach the supplied number sheet here to indicate the camera number. b POWER switch/CAM (camera) and MAIN indicators The POWER switch turns on or off the power supply to the entire camera system, including the CCU-590/590P, the video camera, and the remote control unit connected to the REMOTE connector on the CCU-590/590P. The MAIN and CAM indicators light when the POWER switch is turned on. The CAM indicator goes off when the power is turned off by the CAM PW button on the remote control panel or the

master setup unit, or CAM POWER switch on the internal AT board.
Note

If the fan in the CCU-590/590P stops, the MAIN indicator will flash to warn you of the abnormal condition. If this occurs, turn the POWER switch off immediately and contact Sony service personnel. c CABLE ALARM indicators OPEN: Lights when no triax cable is connected to the CAMERA connector on the rear panel of the CCU590/590P, or when the load current is extremely low even when a camera cable is connected. SHORT: Lights when there is a current overflow in the triax cable. d INCOM audio input/output/setting section INCOM (intercom) connector (XLR, 5-pin) Connects a headset. INCOM level control Adjusts the input level of the intercom.

6

Function and Location of Parts and Controls

MIC/PGM (program audio) switch ON: Turns on the headset microphone. OFF: Turns off the headset microphone. PGM: Outputs the program audio when the one ear headset is used. When this position is selected, the INCOM level control adjusts input level of the program audio. The level of the PGM1 and PGM2 can be adjusted by using the VR located on the panel side of the internal AU board.

INCOM (intercom) selector Selects the pathway of intercom signals output/input through the INCOM/TALLY/PGM connector. PROD: Producer line. PRIV: Producer line and engineer line are cut off and communication is possible only between the CCU590/590P and the camera connected to the rear panel of the CCU-590/590P. ENG: Engineer line. The settings regarding the output intercom signals can be performed on the internal AU board. For details, consult your Sony service personnel.

Rear panel

a CAMERA connector b AUDIO OUTPUT connectors c INPUT connectors d OUTPUT connectors e REMOTE connector f ETHERNET connector

j AC IN connector i WF MODE connector h MIC REMOTE connector g INTERCOM/TALLY/PGM connector

a CAMERA connector (triax connector) Connects to the CA-570/570P/590/590P/905K/F/T/L Camera Adaptor attached to the BVP-E10/E10P/E10WS/ E10WSP/E30/E30P/E30WS/E30WSP Color Video Camera using a triax cable.

Caution

Do not use a defective triaxial cable. The inner sheath of a triaxial cable is used for power supply and the outer sheath for safety ground.

Function and Location of Parts and Controls

7

For your safety, do not use a triaxial cable whose inner and outer sheaths are short-circuited. Use of such a cable will cause electric shock. b AUDIO OUTPUT connectors (XLR, 3-pin) Supply audio signals from the video camera. c INPUT connectors The REFERENCE INPUT connectors, RET-1 connectors, and the RET-2/PROMPTER connectors are loop-through connectors.
A REFERENCE INPUT connectors

D SDI (serial digital interface) RET-3/4 (return video signal 3/4) connectors (BNC type) Accept SDI return video signal. (These connctors are not loop-through connectors.) For details on the selection of RET-3 or RET-4, refer to Operation Manual that came with the camera or camera adaptor. E COAX (coaxial) connector (BNC type) Accepts and supplies signal from/to the video camera using a coaxial cable. Power is not supplied to the camera or a camera adaptor through this connector. To use this connector, it is required to change the setting of the internal board. For details, consult your Sony service personnel. F SPARE connector (BNC type) Not used. d OUTPUT connectors
A VBS/SDI-1, VBS/SDI-2, VBS/SDI-3 connectors

B RET-1 connectors C RET-2/PROMPTER connectors

D SDI RET-3/RET-4 connectors

E COAX connector F SPARE connector

A REFERENCE INPUT connectors (BNC type) The upper connector accepts reference signals (black burst signal) for external synchronization. The input signal is output from the lower connector. The reference input signal can be terminated at 75 ohms internally. To terminate the signal, input the reference signal to the upper connector. B RET-1 (return video signal 1) connectors (BNC type) The upper connector accepts return video signal. The input signal is output from the lower connector. For details on the selection of RET-1, refer to Operation Manual that came with the camera or camera adaptor. C RET-2 (return video signal 2)/PROMPTER connectors (BNC type) The upper connector accepts return video signal or teleprompter signal. The input signal is output from the lower connector. The signal is split and output to the RET2 and PROMPTER signal lines. For details on the selection of RET-2, refer to Operation Manual that came with the camera or camera adaptor. Use the switch on the internal board to output the prompter signal. For details on the internal boards, consult your Sony service personnel.

B Y-G, R-Y/R, B-Y/B connectors

C PIX connector D SYNC connector E WF connector

A VBS (composite video signal)/SDI (serial digital interface)-1, VBS/SDI-2, VBS/SDI-3 connectors (BNC type) Supply the signal from the video camera in composite or SDI format. Use the switch on the internal board to select the composite video signal or SDI signal. For details on the internal boards, consult your Sony service personnel. B Y/G, R-Y/R, B-Y/B (component video signal/RGB output) connectors (BNC type) Supply the component signals or the R, G, and B signals for the chroma keyer from each connector. Use the switch on the internal board to select the signals to be output. For details on the internal boards, consult your Sony service personnel.

8

Function and Location of Parts and Controls

C PIX (picture monitor output) connector (BNC type) Supplies a video signal or video and character signals together to a picture monitor. Use the PICTURE MONITOR button on the MSU-900/ 950, MONITOR SELECT button on the RCP-750/751, and MONITOR SELECT control on the RM-B750 to select the signal output from the PIX connector. When the signal output from the PIX connector on the RCP-750/751 or the RM-B750 changes, the waveform output on the waveform monitor also changes. D SYNC connector Connect to the synchronous signal input connector on a waveform monitor or picture monitor. E WF (waveform monitor output) connector (BNC type) Supplies a video signal to a waveform monitor. The WAVEFORM MONITOR button on the optional MSU-900/950, MONITOR SELECT button on the RCP750/751, or MONITOR SELECT control on the RM-B750 selects the signal output from the WF connector. Changing the signal output from the WF connector on the RCP-750/ 751 or the RM-B750 simultaneously changes the picture on the picture monitor. e REMOTE (remote control) connector (8-pin) Connects to the MSU-900/950 Master Setup Unit, RCP750/751 Series Remote Control Panel or RM-B750 Remote Control Unit with an optional CCA-5-xx connecting cable to transmit/receive control signals. f ETHERNET connector Supports the Ethernet system. For details, consult your Sony service personnel.
CAUTION

h MIC REMOTE (microphone remote control) connector (D-sub, 15-pin) Connects to an external control unit such as an audio mixer. With the connected unit, you can set the microphone input level of the video camera to –60, –50, – 40, –30, or –20 dB. i WF MODE (waveform monitor mode) connector (4-pin) Connects to the corresponding connector on a waveform monitor to allow the sequential monitoring of signals. j AC IN (AC power input) connector Connects to an AC power source using the supplied AC power cord. Secure the power cord to the CCU-590/590P using the supplied plug holder.

For safety, do not connect the connector for peripheral device wiring that might have excessive voltage to this port. Follow the instructions for this port.
PR?CAUTION

Par mesure de sécurité, ne raccordez pas un connecteur pour c?blage de périphérique qui pourrait avoir une tension excessive à ce port. Suivez les instructions pour ce port.
ACHTUNG

Aus Sicherheitsgründen nicht mit einem Peripherieger?tAnschluss verbinden, der zu starke Spannung für diese Buchse haben k?nnte. Folgen Sie den Anweisungen für diese Buchse. g INTERCOM/TALLY/PGM (program audio) connector (D-sub, 25-pin) Inputs/outputs intercom, tally, or program audio signals. Connects to an intercom, tally, or program audio connector of an intercom system.

Function and Location of Parts and Controls

9

Internal power switch and internal boards

Internal boards

AT

EN

IV

AU

TR

DM

ON

Internal power switch

Internal power switch
When abnormality has occurred and power cannot be cut off by pressing the POWER switch on the front panel, open the front panel and turn off this power switch.

Internal boards
Refer to System Manual.

10

Function and Location of Parts and Controls

Connecting the CCU-590/590P to the Video Camera
When connecting a CCU-590/590P to a BVP-E10/E10P/ E10WS/E10WSP/E30/E30P/E30WS/E30WSP Color Video Camera, you must first attach the CA-570/570P/ 590/590P Camera Adaptor to the video camera. A large lens and the BVF-77/77CE 7-inch Viewfinder are connected to the CCU-590/590P through the CA-905K/F/ T/L series large-lens adaptor and the BKP-9057 Viewfinder Saddle, as shown in the illustration below.

CA-570/570P/590/590P

Triax cable

BVP-E10/E10P/E10WS/E10WSP/ E30/E30P/E30WS/E30WSP

When a large lens is used
BVF-77/77CE CA-590/590P BVP-E10/E10P/E10WS/E10WSP/ E30/E30P/E30WS/E30WSP

BKP-9057 CCU-590/590P

CA-905K/F/T/L

To an AC power source

Notes ? The maximum power output from the CAMERA connector of the CCU-590/590P is 110 watts (including a maximum cable loss of 10 watts). Do not connect any equipment which consumes more than 110 watts of power. ? The BVF-7700/7700P Color Viewfinder cannot be used because of the power output rating mentioned above.

Notes on connections
Triax cable
The triax cable should never be connected to or disconnected from the CCU-590/590P when the power is turned on. Always turn the unit off first.

Video camera
Some switches or controls on the video camera may not work when the camera is connected to the CCU-590/590P. For details, refer to Operation Manuals of the video camera and the camera adaptor.

Connecting the CCU-590/590P to the Video Camera

11

Self-Diagnostics
When an RCP-750/751 remote control panel or the RMB750 is connected to the CCU-590/590P, or when a switch on the internal IV board is set, you can display the results of self-diagnostics of the internal boards of the CCU-590/ 590P and other information on a monitor screen. When the RM-B750 is connected to the CCU-590/590P, the information can be viewed on the monitor connected to the PIX or VBS/SDI-3 connector.

Settings of the camera
Press the CHARACTER button on the RCP-750/751 remote control panel or the RM-B750 while the status of the CCU-590/590P is displayed on the monitor screen. The settings on the video camera appears.

BVP (the first column): Model name and format of the connected camera CCU (the second column): Model name and format of the connected camera control unit GEN Lock: The status of the external reference signal Prompter: Transmission direction of the teleprompter signal Dsub15pin: Microphone input level setting performed through the MIC REMOTE connector Return-1 to 4: The settings of the RET-1, RET-2/ PROMPTER, SDI RET-3/RET-4 connectors

Self-diagnostics of the camera system
Press the CHARACTER button on the RCP-750/751 remote control panel or the RM-B750 while the status of the CCU-590/590P is displayed on the monitor screen. The results of a self-diagnosis of the camera system are displayed. Press the CHARACTER button again to display successive pages. Page 1

At the top of the screen, the following items are displayed from left to right: MASTER GAIN, CROP, EVS, SHUTTER, and SHUTTER ON/OFF. At the bottom of the screen, the following items are displayed from left to right: ND FILTER, IRIS, EXTENDER, and CC FILTER. For the meanings of each item, refer to Operation Manuals of the video camera.

Status display of the camera system
Press the CHARACTER button on the RCP-750/751 remote control panel or the RM-B750 while the video camera status is displayed on the monitor screen. The status of the camera system appears.

TRIAX TYPE: Type of Triaxial circuit TRIAX Cable: Triax cable connection status (connected/ disconnected)

12

Self-Diagnostics

TRIAX Comp.: Cable compensation of a triax cable (automatic/manual) TRIAX Step: Compensation step of the triax cable (step indication in the circuit) (The cable length may not be displayed correctly.) Fan Power: Fan status in the CCU power block Timer: Power up time to devices connected CCU Power: Status of the CCU power supply SerialNo: Serial number of the CCU Page 2

Intercom CCU: CCU intercom selection Intercom CAMERA CH1: Status of intercom 1 of the camera (producer line/engineer line) CHU MIC Gain: Gain and control status of the microphone circuit Page 4

Shows the settings of the Ethernet system. For details, contact your Sony service personnel. CAMERA Cable: Camera cable connection status (connected/shorted) CAMERA Data: Camera data transmission status CAMERA Power: Power supply status of the camera CAMERA Tone: Camera ID tone status RCP Cable: Connection status of the REMOTE connector (connected/shorted) RCP Data: Data transmission status of the REMOTE connector RCP Power: Power supply status of the REMOTE connector The following items are displayed only when the F panel is connected. F-PANEL Cable: F-panel cable connection status (connected/shorted) F-PANEL data: F-panel data transmission status F-PANEL Power: Power supply status of the F-panel Page 3

Self-diagnostics results of the CCU590/590P internal boards
Press the CHARACTER button on the RCP-750/751 series remote control panel or the RM-B750 while the results of the Ethernet self-diagnostics page is displayed on the monitor screen. The results of a self-diagnosis of the CCU590/590P internal boards are displayed. Press the CHARACTER button again to display successive pages. For details on the internal boards, refer to the System Manual. DM board

CAM Video: Status of the Y, R-Y, and B-Y signals of the triax signal

Self-Diagnostics

13

Skin Gate: Reception status of the Skin gate signal from the camera TRIAX Comp.: Cable compensation of a triax cable TRIAX Step: Compensation step of the triax cable (step indication in the circuit) (The cable length may not be displayed correctly.) Power: DM board power supply status TR board

AU board

Prompter: Setting status of the prompter line Tone: Tone signal status Incom: Demodulating status of the intercom line CHU Data: Data reception status from the camera Power: TR board power supply status Board ID: ID number of the TR board AT board

MIC: Audio embedding for the main SDI video signal. FRON INCOM: Settings of the front intercom INCOM: Channel setting for the intercom made on the video camera PGM: Program audio setting Audio PLL: PLL staatus of the audio signal Power: AU board power supply status CN: CN board power supply status PLD: PLD status on the AU board Board ID: ID number of the AU board IV board

Reference: Operation mode of the phase adjustment Gen Lock: Locking status CCU Power: CCU power supply type (AC/DC) and power supply status BATT Volt: Voltage of the coin battery supplied with the AT board PLL Volt: Status of the PLL circuit of the AT board CCU Mode: Operation mode of the CCU PLD Config: Configuration result status of the PLD mounted on the AT board Board ID: ID number of the AT board

RETURN: Input settings for the return channels 1 to 4 MIX-Y: Setting for camera signal to be mixed with the return signal Power: IV board power supply status DIF: Status of the DIF connected to the rear of the IV board PLD: Status of the PLD mounted on the IV board Board ID: ID number of the IV board

14

Self-Diagnostics

EN board

displayed on the monitor screen. The ROM version of each device within the system is displayed.

Component: Setting status of the component output signal from the OUTPUT connector and status of the sync signal added to the component Y/G output signal from the OUTPUT connector Composite: Setting status of the composite output signal from the OUTPUT connector Power: EN board power supply status VDA: Power supply status of the VDA board on the rear PLD: Status of the PLD mounted on the EN board Board ID: ID number of the EN board

Exiting the Self-diagnostic mode
Press the CHARACTER button on the RCP-750/751 remote control panel or the RM-B750 repeatedly to display the ROM version indication page, then press the CHARACTER button again.

When an error occurs
The error message is displayed on the picture monitor. In such a case, the self-diagnostics page corresponding to the board where the error has occurred appears by pressing the CHARACTER button. When you keep pressing the CHARACTER button, pages are automatically turned to a screen with no characters (character OFF screen).

Self-diagnostics results of the camera internal boards
Press the CHARACTER button on the RCP-750/751 remote control panel or the RM-B750 while the last page of the results of the self-diagnostics of the CCU-590/590P internal boards is displayed on the monitor screen. The results of a self-diagnosis of the internal boards of the camera are displayed.

ROM version indication
Press the CHARACTER button on the RCP-750/751 remote control panel or the RM-B750 while the results of self-diagnostics of the camera internal boards are

Self-Diagnostics

15

Specifications
General
Power consumption 100 - 240 V AC, 50/60 Hz, maximum 1.8 A Peak inrush current (1) Power ON, current probe method: 50 A (240 V) (2) Hot switching inrush current, measured in accordance with European standard EN55103-1: 10 A (230 V) Cable length Maximum 750 m (φ 8.6 mm) Operating temperature –10°C to +40°C (14°F to 104°F) Dimensions 200 × 124 × 365 mm (8 × 5 × 143/8 in.) (w / h / d) not including projecting parts Mass Approx. 5.5 kg (12 lb 2 oz)

700 mVp-p, 75 ohms BNC type (1) 1.0 Vp-p, 75 ohms WF BNC type (1) NTSC: 714 mVp-p, 75 ohms PAL: 700 mVp-p, 75 ohms Encoded output: 1.0 Vp-p, 75 ohms WF MODE 4-pin (1) AUDIO OUTPUT XLR, 3-pin 0 dBu/-20 dBu, balanced, 2 channels SYNC BNC type (1) 0.3 Vp-p, 75 ohms PIX
3)

The signal selection (VBS or SDI) output from the VBS/SDI 1/2/ 3 connectors is switchable. 4) R/G/B and Y/R-Y/B-Y are switchable.

Camera input/output signals
Triax (Kings type for the U.S.A. and Canada, Fischer type for Europe) COAX BNC type (1), 75 ohms REMOTE 8-pin, multiconnector ETHERNET IEEE 802.3 10BASE-T, IEEE 802.3u 100BASE-TX INTERCOM/TALLY/PGM D-sub, 25-pin (1) 4W/RTS TALLY: 24 V DC, TTL level or contact selectable MIC REMOTE D-sub, 15-pin (1) INCOM (on the front panel) XLR, 5-pin (1) CAMERA

Input signals
REFERENCE RET 1/21) PROMPTER1) SDI RET 3/42) BNC type (loopthrough) VBS/BS, 1.0 Vp-p, 75 ohms BNC type (1 each, loopthrough) VBS, 1.0 Vp-p, 75 ohms BNC type (loopthrough) 1.0 Vp-p, 75 ohms BNC type (1 each) VBS, 1.0Vp-p, 75 ohms (terminated internally) SDI format, 270M bps, SMPTE259M

Supplied accessories
AC power cord (1) AC power plug holder (1) 4-pin connector (1) Number plate (1 set) Operation Manual (1)

1)

The same signal is input to the RET-2 connectors and the PROMPTER connector. 2) The signal selection (SDI or VBS) input to the SDI-RET 3/4 connectors is switchable.

Output signals
VBS/SDI 1/2/33) BNC type (1 each) VBS, 1.0 Vp-p, 75 ohms SDI format, 270M bps, SMPTE259M Y/R-Y/B-Y video4) BNC type (1 each) Y: 1.0 Vp-p, 75 ohms R-Y/B-Y: U.S.A. and Canada: 700 mVp-p, 75 ohms Europe: 525 mVp-p, 75 ohms R/G/B video4) BNC type (1 each)

Optional accessories
Extension board (service parts) Remote Control Unit RM-B750 Rack Mount Adaptor RMM-301 Design and specifications are subject to change without notice.

16

Specifications

The material contained in this manual consists of information that is the property of Sony Corporation and is intended solely for use by the purchasers of the equipment described in this manual. Sony Corporation expressly prohibits the duplication of any portion of this manual or the use thereof for any purpose other than the operation or maintenance of the equipment described in this manual without the express written permission of Sony Corporation.

Trademark
Ethernet is a registered trademark of Xerox Corporation.

CCU-590/590P (UC/CE) 3-869-646-01 (1)

Sony Corporation
B & P Company

Printed in Belgium 2005.03.08 ? 2005


相关文章:
更多相关标签: